https://doc.pinetek-networks.com/ 2026-11-02T15:15:06+00:00 https://doc.pinetek-networks.com/ https://doc.pinetek-networks.com/lib/exe/fetch.php?media=wiki:logo.png text/html 2026-10-20T09:45:22+00:00 Anonymous (anonymous@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:sw:3_binary-protocol:3.7_cmd-status2&rev=1792489522&do=diff 3.7 CMD_STATUS2 The status2 command returns the status of the corresponding port, including an additional hardware error byte from the MAX14819 channel status register. It is an extended version of CMD_STATUS (0x06). Command: Octet # Usage 0 Command ID = 0x08 text/html 2026-10-18T18:58:03+00:00 Anonymous (anonymous@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:sw:3_binary-protocol:3.4_cmd-read&rev=1792349883&do=diff 3.4 CMD_READ This command reads a parameter with the index and subindex as given on the corresponding port. Command: Octet # Usage 0 Command ID = 0x04 1 Port index 0x00 or 0x01 2..3 Index, 16-bit value 4 Subindex 5 Length The **Length ** text/html 2026-10-12T02:03:08+00:00 Anonymous (anonymous@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:sw:3_binary-protocol:3.8_cmd-status3&rev=1791770588&do=diff 3.8 CMD_STATUS3 The status3 command returns the chip-level status register of the MAX14819 transceiver. Unlike CMD_STATUS and CMD_STATUS2, this command is not port-specific and requires only a single command byte (no port index). The returned value is the content of the MAX14819 REG_Status register (0x1E) OR'd with any error bits that were latched since the last call to CMD_STATUS3. Reading this command clears the latch. text/html 2026-10-08T04:00:20+00:00 Anonymous (anonymous@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:sw:3_binary-protocol:3.5_cmd-write&rev=1791432020&do=diff 3.5 CMD_WRITE This command writes a parameter with the index and subindex as given on the addressed port. Command: Octet # Usage 0 Command ID = 0x05 1 Port index 0x00 or 0x01 2..3 Index, 16-bit value 4 Subindex 5 Length 6.. Write Data text/html 2026-09-28T22:06:03+00:00 Anonymous (anonymous@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:sw:3_binary-protocol:3.6_cmd-status&rev=1790633163&do=diff 3.6 CMD_STATUS The status command returns the status of the corresponding port. Command: Octet # Usage 0 Command ID = 0x06 1 Port index 0x00 or 0x01 Return Success: Octet # Usage Comment 0 Command ID = 0x06 1 Port index 0x00 or 0x01 text/html 2026-09-15T19:50:11+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-core:hw:06_compliance&rev=1789501811&do=diff 6. Compliance Requirements Compliance assessment for the regions EU, US, and Canada (not legally binding). The IOL Core4 is an extension board for integration into control, testing, or measurement hardware; it is not a standalone device and is only sold as a component for integration into other products. text/html 2026-09-15T19:49:56+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:hw:3_specifications-support-supplier:3.3_supplier&rev=1789501796&do=diff 3.3 Supplier information Pinetek Networks GmbH Bachstelzenweg 8 DE-88677 Markdorf www.pinetek-networks.com info@pinetek-networks.com Disposal The IOL HAT is marked with the crossed out waste bin symbol with shows the compliance with the WEEE. Pinetek Networks will take back devices that are used in a B2B environment. For devices, that are used in B2C environments, the local disposal through local services, or they can be returned to Pinetek Networks. text/html 2026-09-15T19:49:01+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:hw:3_specifications-support-supplier:3.1_technical-specifications&rev=1789501741&do=diff 3.1 Technical Specifications Transceiver * Dual IO-Link Master Transceiver Analog Devices MAX14816 with Integrated Framers and L+ Supply Controllers * SPI-Mode only (RX/TX not used) Mechanical Dimensions * 65,5 × 66 mm * Height: 18 mm with stack-through text/html 2026-09-15T19:48:26+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-core:hw:04_interface&rev=1789501706&do=diff 4. Interface 4.1 General Considerations * The host connector and IOL connectors are 2,54mm pitch pin header with a pin length of 6mm. * The clearance under the board shall be min. H=3,5mm. 4.2 Power Supply * The 24V power supply voltage shall be 24V +/- 20%. text/html 2026-09-15T19:47:42+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:hw:2_connections:2.2_40-pin-gpio-jumpers&rev=1789501662&do=diff 2.2 40-pin GPIO to Raspberry Pi and jumper settings (PT-1201 only) This connector provides the connection to the Raspberry Pi over the standard 40-pin GPIO connector: This connector is implemented as stack-through, i.e. up to two IOL HATs can be connected on top of each other. If the pins are not occupied by the connected IOL HAT, additional expansion boards can be connected via the stack-through connector. text/html 2026-09-15T19:47:20+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-core:hw:03_outlines_connector_positions&rev=1789501640&do=diff 3. Outlines and Connector Positions 3.1 Top and Bottom Definition Ensure the correct orientation of the IOL Core4 module. Misalignment or rotation can cause damage on the host system and the IOL Core4. Do not plug or unplug while powered. 3.2 Outlines and Positions (TOP View) text/html 2026-09-15T19:45:15+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-core:hw:05_environmental_requirements&rev=1789501515&do=diff 5. Environmental Requirements Operating temperature range: -25°C to +60°C. The IOL Core4 was tested with a host board with an environmental temperature of 50°C. The final temperature rating needs to be done with the host hardware in the integrated setup. text/html 2026-09-15T19:44:15+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-core:hw:02_system_architecture&rev=1789501455&do=diff 2. System Architecture 2.1 IOL Core4 2.2 IOL Core4 Pro text/html 2026-09-15T19:43:10+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-core:hw:01_introduction&rev=1789501390&do=diff 1. Introduction 1.1 Purpose The IOL Core4 is a compact IO-Link® master module designed for integration into embedded host systems. It provides four IO-Link ports compliant with IEC 61131-9 (SDCI), enabling direct connectivity to industrial sensors and actuators in IIoT and automation applications. text/html 2026-09-15T19:42:02+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=iol-hat:hw:1_basics:1.1_introduction&rev=1789501322&do=diff 1.1 Introduction Thanks for purchasing an IOL HAT module. Please read this information carefully to ensure safe and hassle-free operation of the device. The application of this product is intended for users, that have experience with electronic devices and programming. text/html 2026-09-15T19:40:18+00:00 anla (anla@undisclosed.example.com) https://doc.pinetek-networks.com/doku.php?id=wiki:ebook:iol_core_hw&rev=1789501218&do=diff iol_core_hw * 1. Introduction * 2. System Architecture * 3. Outlines and Connector Positions * 4. Interface * 5. Environmental Requirements * 6. Compliance Requirements